Momental homeMomental

Sound mixer

Layer deep hum, brown, pink and white noise at independent levels, shape the top end, and share your mix as a link.

By Christian Krueger · Last updated

Blend the layers, then share the link to your mix.

Starting point
Layers
Sleep timer

Not medical advice. This tool is for general comfort and information only and gives no diagnosis. If you have a persistent health concern, speak to a qualified professional.

How to build a mix

Start from one of the three presets, then move the layers until the sound you are trying to cover stops pulling your attention. The order on screen runs low to high: deep hum sits under everything, brown fills the low-mid, pink is the natural middle, and white adds the bright top.

Two controls shape the finished mix rather than its balance. Warmth is a low-pass filter across everything — turn it down and the whole mix retreats behind a wall; turn it up and it opens out. Master volume should be the last thing you touch, and it should end up lower than you expect.

When a mix works, use Copy link to this mix. Every level, the warmth, the volume and the timer are encoded in the URL, so the link reproduces it exactly. Nothing is uploaded and there is no account.

Why layering beats a single noise colour

A single colour is one fixed slope across the spectrum. That is fine when your problem is broadband, but most real problems are not.

Footsteps overhead, a bass line through a floor, and traffic are almost entirely low-frequency. Brown noise and a deep hum cover those, and adding treble does nothing except make the mix tiring. A television through a wall, a conversation, or a dog is the opposite: the information you keep noticing is in the mid and high range, so a little pink and white does more than a lot of brown.

Layering also solves the loudness problem. Matching a single colour against a specific noise usually means turning the whole thing up until the relevant part is loud enough, which makes every other part louder than it needs to be. Putting energy only where you need it lets the overall level sit lower — which matters most for anything running all night.

What the warmth control actually does

Warmth is a single low-pass filter after the mixer, sweeping from about 300 Hz to 18 kHz.

Rolled all the way down, only the lowest content survives, and the mix sounds like it is coming from another room. That is often exactly right for sleep: less high-frequency detail is easier to tolerate over hours, and it stops a bright mix from sounding like a hiss you are listening to rather than through.

Opened up, the mix keeps its full top end, which masks sharp transient sounds far more effectively. That is the setting to use for a noisy office or a shared workspace.

Volume, and the one real risk

Sound masking is comfortable, not therapeutic, and the only genuine hazard here is level. Set it as low as the job allows. If you are raising your voice over it, or you can still hear it clearly as a separate thing after a couple of minutes, it is too loud.

Be more conservative again for overnight use and for children, whose exposure is longer and whose thresholds are lower. The Sleep Foundation's overview of noise and sleep covers the trade-offs, and the NIDCD is the place to start if tinnitus is the reason you are here. None of this is medical advice.

What this page cannot do

The mixer runs entirely in the browser, which is why it needs no account — and also where it stops. Close the tab and it ends. Lock your phone and most browsers suspend the audio within seconds, which also kills the timer. The mix lives in a URL rather than in a library, so there is no way to keep a set of named mixes and move between them.

Background playback with the screen off, a timer and alarm that survive the lock screen, and saved mixes that sync across devices need a native app. Those are the gaps, stated plainly, so you can decide whether this page is enough for you.

Frequently asked questions

Why layer noise instead of just picking one colour?
A single colour is one fixed balance across the whole spectrum. Layering lets you put the energy where your problem actually is — heavy low end to cover footsteps and traffic through a wall, a little white on top to blunt sharp sounds like a door or a voice, and nothing in between to keep it from sounding harsh.
What does the warmth control do?
It is a low-pass filter across the finished mix. Turning it down removes high frequencies, which makes everything sound more distant and muffled — closer to noise heard through a wall. Turning it up leaves the mix open and bright. It changes the character without changing the balance you set.
Can I save or share a mix?
Yes. "Copy link to this mix" puts every level, the warmth setting, the volume and the timer into the URL, so bookmarking it or sending it to someone reproduces the exact mix. Nothing is stored on a server and no account is involved.
How loud should I set it?
Only as loud as it needs to be to cover the sound that bothers you, and no louder. If you are raising your voice over it, or you are still aware of it after a couple of minutes, turn it down. Sustained loud playback carries real hearing risk, especially overnight and especially for children.